| ACCESS | menu_setting | — | Per-channel page (red, green, orange) where each of 16 locations can be enabled or disabled. Enabled locations are visited by the sequencer; disabled locations are skipped or slept through depending on FUN.OP.SLEEP setting.238 |
| CV Programming Grid (Knobs) | knob | — | 16 illuminated knobs arranged in a 4x4 grid. Each knob sets the CV output value for the corresponding location on the currently selected channel. Changes are applied when the sequence reaches that location.238 |
| FUN.CV.ADD | menu_setting | — | Adds the channel's CV input to the current location value, then quantizes if quantizer is active. Not available on C/Orange channel. Mutually exclusive with FUN.CV.S&H.238 |
| FUN.CV.LOC | menu_setting | — | Allows CV input to directly address the channel's location along the active snake pattern. For C/Orange, CV range for addressing is 1/4 that of X/Y channels. CLK input still increments the sequence start point.238 |
| FUN.CV.S&H | menu_setting | — | Like FUN.CV.ADD but CV addition is only updated on rising edge of MOD input (sample and hold). Not available on C/Orange. Mutually exclusive with FUN.CV.ADD.238 |
| FUN.CV.SNAKE | menu_setting | — | When enabled, CV input selects the snake pattern. Has no effect on C/Orange channel. When turned off, the currently selected snake pattern is retained.238 |
| FUN.MOD.CLK | menu_setting | — | Combines CLK and MOD inputs to drive the axis. CLK is read as variable-width gate; MOD is read as rising-edge trigger. When MOD is unpatched, button acts as manual clock advance.238 |
| FUN.MOD.RESET | menu_setting | — | Resets channel to nearest access-enabled location to location 1 on rising edge of MOD input. When MOD is unpatched, button acts as manual reset toggle.238 |
| FUN.MOD.RUNSTP | menu_setting | — | Channel runs when MOD gate is high, stops when low. Mutually exclusive with FUN.MOD.DIR. When unpatched, button toggles run/stop manually.238 |
| FUN.OP.SCAN | menu_setting | — | Scans all 16 knobs and writes their current physical positions onto the current channel, instantly applying knob values.238 |
| FUN.OP.SLEEP | menu_setting | — | When SLEEP OFF: sequence skips past non-accessed locations (SEEK). When SLEEP ON: CV output rests for one clock at each non-accessed location before moving on.238 |
| FUN.OP.TRIG | menu_setting | — | OFF: gate output follows clock width. ON: gate output is a short trigger. As of V133 firmware, gate-tie behavior is added: locations with both Gate and Glide enabled stay high until a non-Glide-enabled location is reached.238 |
| GATE | menu_setting | — | Per-channel page enabling or disabling gate output per location. Gate width follows clock input width or outputs short trigger depending on FUN.OP.TRIG setting.238 |
| GBL.BUS | menu_setting | — | Controls Select Bus behavior. FREE (default): ignores Select Bus. LEAD: transmits state changes, multi-paste, mesh, and store commands to following modules. FOLLOW: René changes state to match commands received on Select Bus.238 |
| GBL.STORE | button | — | Stores all states and global settings to non-volatile memory. René stops sequencing during the 8-10 second store process. M-Paste and Latch settings are not stored. The active state at store time is loaded on next power-up.238 |
| GBL.Z.RESET | menu_setting | — | When ON, state changes via Z-MOD also reset all three channels (X, Y, C) to the access-enabled location nearest to location 1. Also applies to manual state selection on State Select page.238 |
| GL.Z.ON | menu_setting | — | When ON: Z-MOD and Z-CV select states globally from all pages. When OFF: Z-MOD and Z-CV only work on the State Select page.238 |
| GLIDE | menu_setting | — | Per-channel page enabling portamento per location. For X and Y channels glide time follows clock rate; for Cartesian channel glide time is a constant.238 |
| Octave Range (QUANT top row) | menu_setting | 1octave – 4octave | 238 |
| QUANT | menu_setting | — | Per-channel quantizer. Bottom three rows select notes from the 12-tone equal-tempered scale. Top row selects octave range (1-4 octaves). No octave range selected means maximum output range/resolution with no quantization.238 |
| SNAKE | menu_setting | — | Available for X and Y channels only (not C/Cartesian). Selects one of 16 snake patterns determining the path the sequence takes through the 4x4 grid. CV input can also select snake pattern when FUN.CV.SNAKE is enabled.238 |
| X-CV Combo Pot | knob | — | Input attenuator for X-CV jack with 5V normalization. When nothing is patched, acts as a panel control with the 5V normal allowing manual CV selection.238 |
| Y-CV Combo Pot | knob | — | Input attenuator for Y-CV jack with 5V normalization. When nothing is patched, acts as a panel control with the 5V normal allowing manual CV selection.238 |