alm-busy-circuits/squid-salmple

ALM Busy Circuits Squid Salmple Audio Buffer Recording / Looper · Sample Player

21 HP audio buffer recording / looper and sample player by ALM Busy Circuits: 17 inputs, 6 outputs, 17 controls, 13 modes.

ALM Busy Circuits · ALM-022 Squid Salmple Manual v0.7 (firmware 188) (PDF) ↗

Sample Player · Audio Buffer Recording / Looper · CV Recorder / Gesture Looper · Multimode Filter · Distortion / Saturation · Reverse playback · 1V/Oct Pitch Tracking

Inputs 17

Inputs
JackWhat it doesRangeConnections
Trigger Input 1 179channel playback trigger
trigger, gate
—
→ Channel 1
Trigger Input 2 179channel playback trigger
trigger, gate
—
→ Channel 2
Trigger Input 3 179channel playback trigger
trigger, gate
—
→ Channel 3
Trigger Input 4 179channel playback trigger
trigger, gate
—
→ Channel 4
Trigger Input 5 179channel playback trigger
trigger, gate
—
→ Channel 5
Trigger Input 6 179channel playback trigger
trigger, gate
—
→ Channel 6
Trigger Input 7 179channel playback trigger
trigger, gate
—
→ Channel 7
Trigger Input 8 179channel playback trigger
trigger, gate
—
→ Channel 8
V/O 6 179channel 6 pitch
pitch
scaling v oct
→ Channel 6, Quant
V/O 7 179channel 7 pitch
pitch
scaling v oct
→ Channel 7, Quant
V/O 8 179channel 8 pitch
pitch
scaling v oct
→ Channel 8, Quant
CV 1 179assignable CV input
cv, trigger
0 to 5 V, unipolar
→ assigned parameter
attenuated by Assign 1
CV 2 179assignable CV input
cv, trigger
0 to 5 V, unipolar
→ assigned parameter
attenuated by Assign 2
CV 3 179assignable CV input
cv, trigger
0 to 5 V, unipolar
→ assigned parameter
attenuated by Assign 3
Signal 179sample input
audio, cv
—
→ Recorder
attenuated by Level
Rec 179record trigger
trigger, gate
—
→ Recorder
In 2 modes
  • short trigger (<500ms): record until signal drops → Record envelope follower
  • gate (>500ms): record while high → Recorder
Chan 179channel input
trigger
—
→ Recorder, Sample channels
In 7 modes
  • Activate next channel: steps active channel → Recorder
  • Choke all Channels: stops all playback → Sample channels
  • Punch in record cue set: adds cue set → Recorder
  • Load next bank: loads next bank → Sample channels
  • Reset all cue steps: resets stepped cue sets → Sample channels
  • Reset all Step triggers: resets Steps channels → Sample channels
  • Toggle Record Monitor: toggles record monitor → Recorder

The documents don't state: voltage, polarity (V/O 6, V/O 7, V/O 8, Signal); threshold (Trigger Input 1, Trigger Input 2, Trigger Input 3, Trigger Input 4, Trigger Input 5, Trigger Input 6, Trigger Input 7, Trigger Input 8, Rec, Chan); coupling, impedance (V/O 6, V/O 7, V/O 8, CV 1, CV 2, CV 3, Signal); audio rate (Signal).

Outputs 6

Outputs
JackWhat it doesRangeConnections
Trigger 179record gate, E Trig
gate, trigger
—
from Recorder, Sample channels
Mix Out 179mix of unpatched channels
audio
coupling ac
from Mix, Channel 1, Channel 2, Channel 3, Channel 4, Channel 5, Channel 6, Channel 7, Channel 8
1+2 Out 179channel pair output
audio, cv
coupling dc
from Channel 1, Channel 2
3+4 Out 179channel pair output
audio, cv
coupling dc
from Channel 3, Channel 4
5+6 Out 179channel pair output
audio, cv
coupling dc
from Channel 5, Channel 6
7+8 Out 179channel pair output
audio, cv
coupling dc
from Channel 7, Channel 8

The documents don't state: voltage, polarity (Mix Out, 1+2 Out, 3+4 Out, 5+6 Out, 7+8 Out); coupling (Trigger); audio rate, impedance (all outputs).

Controls 17

Controls
ControlWhat it doesAffectsPositions
Program 179encoder: select/adjust/click
knob
Sample channels—
Chan 179channel screen / select
button
Sample channels—
Quality 179cycle quality parameters
button
Quality, Channel filter, Quant
  • Bits: bit depth
  • Rate: playback rate kHz
  • Speed: linear playback speed
  • Pitch: pitch shift multiplier
  • Quant: pitch quantisation (ch 6-8)
  • Filter: filter type
  • Frequency: filter cutoff
  • Resonance: filter resonance
Env 179cycle envelope parameters
button
Envelope
  • Level: playback volume
  • Decay: decay envelope
  • Attack: attack envelope
  • E Trig: end of playback trigger
  • Steps: round robin triggering
Loop 179loop parameters
button
Sample channels
  • Loop: loop mode
  • X-Fade: loop crossfade
Cues 179cycle start/end/loop cues
button
Sample channels
  • Start: playback start
  • End: playback end
  • Loop: loop point
Reverse 179reverse sample
button
Sample channels—
USB 179USB bank screen
button
Sample channels—
Func 179shift / secondary functions
button
Sample channels—
Rec 179arm/start/stop recording
button
Recorder—
Level 179sample input level
knob
Recorder, Signal—
Assign 1 179assign CV to parameter
button
CV 1—
Assign 2 179assign CV to parameter
button
CV 2—
Assign 3 179assign CV to parameter
button
CV 3—
V/O 6 179channel 6 pitch
knob
Channel 6—
V/O 7 179channel 7 pitch
knob
Channel 7—
V/O 8 179channel 8 pitch
knob
Channel 8—

Blocks 8

Blocks and their connections
BlockKindTypesInputsControlsOutputsSource
Sample channels8 sample channelsSamplerTrigger Input 1, Trigger Input 2, Trigger Input 3, Trigger Input 4, Trigger Input 5, Trigger Input 6, Trigger Input 7, Trigger Input 8, V/O 6, V/O 7, V/O 8Program, Quality, Env, Loop, Cues, Reverse1+2 Out, 3+4 Out, 5+6 Out, 7+8 Out, Mix Out179
Channel filterresonant multimode filterFilter—Quality—179
Envelopeattack/decay envelopeEnvelope generator, VCA—Env—179
Qualitybits/rate reductionDistortion / saturation—Quality—179
Quantpitch quantisationQuantizerV/O 6, V/O 7, V/O 8Quality—179
Recordersample recordingLooper, Input / preamp stageSignal, Rec, ChanRec, Level, ChanTrigger179
Record envelope followerinternal envelope followerEnvelope followerRec——179
Mixmix outputMixer——Mix Out179

Modes 13

Modes
ModeKindSelected bySelection methodSource
Replacerecord mode—Program encoder on Sample screen179
Overdubrecord mode—Program encoder on Sample screen179
Extendrecord mode—Program encoder on Sample screen179
Forwardloop mode—Loop parameter179
Looploop mode—Loop parameter179
Zig zagloop mode—Loop parameter179
Gateloop mode—Loop parameter179
LPfilter typeQuality = FilterQuality-Filter179
BPfilter typeQuality = FilterQuality-Filter179
NTfilter typeQuality = FilterQuality-Filter179
HPfilter typeQuality = FilterQuality-Filter179
Randomcue set mode—Cue Sets list179
Stepcue set mode—Cue Sets list179

Hidden functions 19

Hidden functions
FunctionTriggerAffectsSource
cue sets screenFunc + CuesSample channels179
CV attenuation/offsetFunc + AssignCV 1, CV 2, CV 3179
assign CV to Reversehold Reverse + AssignReverse179
mute channelFunc + EnvSample channels179
solo channelChan + Func + EnvSample channels179
reassign outputFunc + Quality1+2 Out, 3+4 Out, 5+6 Out, 7+8 Out179
Chan input configChan + Func + USBChan179
record monitorFunc + Rec7+8 Out, Mix Out179
lock record channelChan + RecRecorder179
clear extended recordinghold Rec + click ProgramRecorder179
manual trigger outFunc + click ProgramTrigger179
same param other channelhold Chan + turn ProgramSample channels179
set param all channelsChan + Func + turn ProgramSample channels179
swap channelshold Chan, turn, FuncSample channels179
choke channelhold Chan + Env + turnSample channels179
BPM displayhold Func on SpeedSample channels179
cue zoomhold Func + turn ProgramSample channels179
system / calibration screenFunc + USBSignal, Mix Out179
firmware updatepower on holding Funcmodule179

Specs 21

Specs
SubjectQuantityValueConditionSource
channelsample time11 s—179
audiobit depth16 bit—179
audiosample rate44.1 kHz—179
triggerresponse time1 to 2 ms—179
modulenoise floor-75 dB—179
SpeedBPM display1 to 300 BPMFunc held, 1 bar179
Env-Levelunity gain value50 value—179
Env-Leveldefault value30 value—179
Decaymax decay time10 slooping sample179
Overdubunderlying audio reduction-3 dB—179
Rec inputshort trigger threshold500 ms—179
V/Orough tracking range2 to 3 octaves—179
banksper bank set99 banks—179
Poolentries per directory256 entries—179
cue setsmaximum64 sets—180
CV inputscount3 inputs—179
AXONextra CV inputs4 inputs—179
modulecurrent +12V300 mA—179
modulecurrent -12V35 mA—179
modulewidth21 HP—179
moduledepth38 mm—179

Properties 12

Properties
SubjectPropertyValueSource
channel outputscouplingDC179
Mix OutcouplingAC179
recordingformat16 bit 44.1kHz mono179
Signallevelmodular to line179
Speed/Pitchavailabilitychannels 1-5179
Quantavailabilitychannels 6-8179
CV assignmentscombinationcumulative179
filtersCPU loadhigh179
wav loadingformats16/24 bit 44.1kHz179
stereo filesloadingmade mono179
StepsCV assignableno179
Chan inputedgerising180

Behavior 24

Behavior rules
SubjectWhenEffectModeSource
pair outputpatchedremoved from mix output—179
CV inputsoutside 0-5Vignored—179
Rec inputtrigger under 500msrecords until signal drops—179
Rec inputtrigger over 500msrecords while high—179
Recordingmax time reachedloops to beginning—179
Extendbuffer fullstops, warns full—179
Overdubrecordingkeeps cue sets—179
Replacerecordingclears cue sets—179
Trigger outrecording activehigh gate—179
Gate looptrigger input highplays and loops—179
Gate looptrigger low, Decay setmoves to decay—179
Cue set changewhile playing/recordingqueued for next trigger—179
Cue set CV0-5Vdivided across cue sets—179
Start pointmoved past looploop point moves forward—179
End pointmoved behind looploop point moves back—179
Auto cuerundeletes existing cue sets—179
RecordingUSB screen activedisabled—179
Monitorenabledinput to output 8—179
Chokechoking channel startstarget channel stops—179
Env-Stepsencoder clickdoes not cycle—179
wav fileslonger than 11struncated—179
Frequency/Resonanceno filter typenot shown—179
Mix Outcarrying CVwon't reproduce CV—179
modulepower onloads last bank—179

Functions 7

Function tags
FunctionBasisScopeEvidenceSource
Sample Playerblockpatchableblock Sample channels: 8 channel sampler179
Audio Buffer Recording / Looperblockpatchableblock Recorder: records Signal to channel179
CV Recorder / Gesture Looperdocumented usepatchabledocumented: sampling and playback of CV179
Multimode FiltercontrolinternalQuality-Filter: LP/BP/NT/HP per channel179
Distortion / SaturationcontrolinternalQuality-Bits/Rate: bit depth, rate179
Reverse playbackcontrolinternalReverse: reverse the sample179
1V/Oct Pitch Trackingjackpatchablejacks V/O 6-8: 1v/oct pitch179

Power

+12 V300 mA
−12 V35 mA
+5 V—
Width21 HP
Depth38 mm

Other Audio Buffer Recording / Looper modules

All Audio Buffer Recording / Looper modules →

Firmware 31

VersionReleasedNotes
190—More fixes for loading very old firmware saved banks.179
189—Fix bug loading banks from earlier firmware versions getting corrupted.179
188—New 'Pitch' parameter for timestretch-like effects. Filter performance improvements. Axon stability improvements.179
187—Minor Pool browsing improvements. Added Axon 2 support.179
186—Improved USB stick compatibility. Chan input can now be assigned to toggle record monitor. Increased per-directory file count to 256. Remember last browsing position in Pool.179
185—Fix issue where stopping recording during playback could cause an audible glitch. Manual updated for new features.179
184-beta—Fix Step T wrap. Fix reverse samples firing E Trigs correctly. Fix Axon-1 expander working with cue sets.179
183-beta—Fix cues & steps correctly resetting to step when chan redirected. Chan input now responds to rising rather than falling edge.179
182-beta—Added alternate chan input rerouting (choke all, punch markers, load next bank, reset steps). Added Step T (round-robin trigger) to Env menu. Fixed pool filename scrolling and load fail handling. Fixed cue set display and skipping issues.179
172—Fixed/corrected quantisation scales. Fixed potential lockup when loading too long a sample into channel 8. Fixed flicker on monitor/record popup.179
167—Fixed filter lockup regression. Removed duplicate 12-tone quantisation option. Minor UI boot tweak.179
165-beta—Added output remapping (Func+Quality moves channel to neighbour output). Increased V/oct quantisation scales. Added 24-bit WAV loading (downsampled to 16-bit). Fixed UI sluggishness, filter resonance at 0, cue set menu on delete, USB boot recognition. Added CV expander (Axon-1) support.179
148—Fixed filter settings not being correctly applied to loaded banks and swapped channels.179
147—New per-channel multimode filter with resonance (under Quality). Added encoder acceleration. Remember last accessed screens. Improved CV-mapped cue set triggering (now immediate). Fixed lockup when channel 8 is full and bit depth fully reduced.179
141—Pool and file handling tweaks. Autochopper improvements including DC offset removal. Clip LED improved for fast transients. Fixed loading WAVs with >64 cue markers. Fixed stereo sample pool preview.179
137-beta—Alphabetically sort Pool filename entries. Fixed channel name updating when channels swapped. Fixed tuning fork rendering over channel filename.179
135-beta—Added Pool directory for free WAV loading. Added bank subdirectory numbered naming. Display channel sample filenames. Fixed bank set menu scrolling and loop symbol rendering.179
129-beta—Added Bank Sets support (multiple sets of banks on same USB). Added attenuation/offset control to CV inputs. Fixed potential lockup when modulating channel 1 loop/end point. Fixed key press handling on special cue set options.179
125—Fixed cue split to 64 sets. Added remove-all-cue-sets option. Extended record warns when channel full; Enc+Rec clears. Fixed extend crasher, short trigger extend, bank number display, bank name sync, and random cue set selection.179
121-beta—Added new recording modes (Overdub/Extend). Tidied Cue Sets screen and added Auto cue creation. Added E Trig screen under Env. Fixed saved cue set offset on crop and lockup on full-length channel 8.179
111—Added 'step' cue set mode (jump to next cue set on trigger). Fixed potential lockup when zig-zag looping a max-length sample on channel 8.179
110-beta—Added single sample preview from Load 1 screen. Added scanning feature when start+end assigned to same CV. Fixed Decay representation for CV control. Fixed chan+enc accessing quant/speed for non-V/oct channels. Improved bank rename UI. Func+Enc BPM screen now more granular.179
108—Added RANDOM cue set and gated loop type. Added BPM display on speed parameter. Fixed marker-to-cue-set conversion, Chan+Func hold, single channel save destination, Decay/Attack at 0V CV, and cue set clearing on new sample.179
100—Fixed Level parameter clamping so it doesn't wrap. Fixed speed/pitch getting messed up when V/Oct channels are swapped.179
99—Added record channel lock feature (Chan+Rec). Throttled record/monitor repaints for better responsiveness.179
97—Added compatibility code for pre-v88 WAV metadata (32 cue sets) to be handled correctly.179
90—Tidied Env & Quality params for sane directions without rollover. Fixed bug where quant option only worked for channel 6.179
88—Added Attack parameter. CV assignments are now cumulative on same param. Increased cue sets to 64. Trim bad cue points rather than aborting load.179
81—Fix to better recognise some USB keys at startup.179
80—Fixed minor cue set bugs, metadata wiped on single sample load, envelope follower stopping when recording via trigger. Improved USB key support. Added Solo and improved mute behaviour.179
71—Initial firmware release.179

Sources 2

  1. [179]
    ALM-022 Squid Salmple Manual v0.7 (firmware 188) ↗manual · primary
    ● verified 2026-05-06
  2. [180]
    ALM Squid Salmple product page ↗product page
    ⚠ verified 2026-05-06 · the manufacturer changed this document since