| Attack | fader | — | Time for the envelope to rise from zero to its maximum level. If the gate or hold ends before maximum is reached, the envelope jumps immediately to release from the current level.1157 |
| Curve Shape | fader | — | Independently shapes the curve of attack, decay, and release between logarithmic and exponential, passing through linear at the midpoint. The classic analog exponential decay is achieved at approximately 70%.1157 |
| Decay | fader | — | Time to fall from maximum level to sustain level after punch completes. When punch duration is zero, decay follows immediately after attack. If gate or hold ends before sustain is reached, envelope jumps to release.1157 |
| Filling | menu_setting | — | Sets how much of a cycle the envelope occupies. At 100% the envelope fills exactly one cycle; below 100% adds a gap after the envelope; above 100% causes overlap with the next cycle. Does not change the cycle duration itself.1157 |
| Full Attack | menu_setting | — | When on, a started attack always completes even if the gate or hold ends early; punch is included. In trigger mode, attack is always full regardless of this setting.1157 |
| Global Morph Time | menu_setting | 0s – 120s | 1157 |
| Global Time | fader | 0% – 800% | A timing multiplier applied to all envelope stage durations simultaneously. At 100% (mid-fader), each stage can reach up to 30 seconds; at 800%, stages can reach up to 4 minutes. At 0%, all envelopes are reduced to a pulse.1157 |
| Hold | fader | — | A virtual gate extension that begins with the Attack phase. If the actual gate is longer than Hold, Hold has no effect. When Hold extends beyond the gate, the envelope remains in sustain until Hold ends, then moves to release.1157 |
| Invert Output | menu_setting | — | When enabled, flips the polarity of the envelope output. The signal remains unipolar positive; no negative voltages are produced.1157 |
| Morph Time | menu_setting | 0s – 120s | Per-preset duration for transitioning all continuous and CV settings from the current preset to a newly called one. Active only in Live mode when Global Morph mode is off. Read from the target preset.1157 |
| Offset | menu_setting | — | Positions the envelope's start point within a cycle. The cycle is divided into 12 equal steps, allowing multiple envelopes to be staggered relative to each other.1157 |
| Output Level | fader | ≤8V | Sets the peak voltage of the envelope output. CV control of this parameter acts as a virtual VCA per envelope channel.1157 |
| Pre-Delay | fader | — | Delays the start of the entire envelope as if the gate arrived later; the end of gate is not delayed. When longer than the gate signal, no envelope occurs. In cycle mode, its percentage is independent and added to the cycle duration.1157 |
| Punch | fader | — | A hold phase at maximum level following the attack, before decay begins. If gate or hold ends before punch completes, the envelope moves immediately to release.1157 |
| Release | fader | — | Time to fall from the current level to zero. Triggered as soon as both the gate and hold durations have ended.1157 |
| Sustain | fader | — | The steady-state level held after attack, punch, and decay phases complete, provided the gate or hold is long enough to reach this point.1157 |
| Tempo | menu_setting | 1BPM – 300BPM | 1157 |
| Transition | menu_setting | — | Determines whether a retriggered attack starts from the current envelope level (Join) or resets to zero first (Restart). The attack duration is unaffected; only the slope changes.1157 |
| Trigger Mode | menu_setting | — | Selects whether the envelope responds to a gate (duration tracks gate length) or a trigger (envelope runs its full course automatically through all phases).1157 |
| User Knob | knob | — | Bipolar manual CV source (negative to zero to positive) that can be assigned in the CV matrix to any modulation destination. At the midpoint it outputs zero, indicated by double off-blips on its LED.1157 |