| Attack | knob | 0% – 100% | Time for the sound to reach peak level; uses a logarithmic scale from 0 to 9 seconds; is a modulation target.977 |
| Beat Count | menu_setting | 1 – 512 | Specifies the number of beats in the clip/slicer WAV for clock synchronization; Auto attempts auto-detection.977 |
| Beat Sync | menu_setting | — | Controls whether a time-based value is measured in musical intervals (synced to clock) or as a percentage. On the Delay FX it switches delay time between musical divisions (1/64 ... 1 bar) and a 0-100% value; Clip-mode pads and the LFO offer the same beat-synchronization choice.977 |
| Brightness | menu_setting | — | Controls the brightness of the display screen.977 |
| Compressor | menu_setting | — | When set to On, applies a compressor to the signals sent to Out 1 and 2. Pads mapped to Outs 3-6 bypass the compressor.977 |
| Cutoff | knob | — | Sets the delay filter cutoff; positive values apply high pass, negative values apply low pass; is a modulation target.977 |
| Damping | knob | 0% – 100% | Controls reverb damping; higher values shorten the reverb tail; is a modulation target.977 |
| Decay | knob | 0% – 100% | Time from initial peak to sustain level; uses a logarithmic scale from 0 to 38 seconds; is a modulation target.977 |
| Delay | knob | 0% – 100% | Sets delay length; when Beat Sync is on uses musical intervals (1/64 to 1 bar); when off uses 0–100%; is a modulation target.977 |
| Density | knob | 0% – 100% | Controls number of grains per second; higher values create more overlapping grains at the cost of processor load.977 |
| Excl Group | menu_setting | — | Assigns the pad to an exclusive group (A–D); triggering any pad in the group stops all others. Excl X disables exclusive behavior.977 |
| Feedback | knob | 0% – 100% | Controls the amount of echo regeneration in the delay; is a modulation target.977 |
| Filter | knob | -100% – 100% | Applies either a low pass filter (negative values) or a high pass filter (positive values) to the pad; is a modulation target.977Zones- Low Pass -100–0%Negative values apply a low pass filter to the pad audio.977
- High Pass 0–100%Positive values apply a high pass filter to the pad audio.977
|
| Gain | menu_setting | — | Recording setting: adjusts the input gain so the signal to be recorded reaches a good level without clipping (the VU meters show the level). Range -96.0 dB to +20.0 dB.977 |
| Grain Size | knob | 0% – 100% | Sets the duration of each grain; 0% is about 20 ms, 100% is about 1 second.977 |
| Interp | menu_setting | — | Selects Normal or High Quality interpolation for chromatic pitch shifting; HighQ reduces aliasing but uses more processor resources.977 |
| Launch Mode | menu_setting | — | Controls how pad playback starts and stops: Trigger (plays to end), Gate (plays while held), or Toggle (plays until next trigger).977 |
| Length | knob | ≥0sample | When Loop Mode is None, determines how many samples play past the Start point; is a modulation target.977 |
| Level | knob | -96dB – 12dB | Adjusts the loudness level of the pad; is a modulation target.977 |
| LFO BeatSyn | switch | — | When ON, synchronizes the LFO wave cycle to the clock and changes LFO Rate to use beat/measure divisions instead of percentage.977 |
| LFO Depth | knob | 0% – 100% | Sets the amplitude of the LFO wave; is a modulation target.977 |
| LFO Rate | knob | 0% – 100% | Controls LFO frequency (about 0.1–12 Hz when BeatSync is off; beat/measure divisions when on); set to 0 to stop the LFO; is a modulation target.977 |
| LFO Trig | switch | — | When ON, the LFO restarts from the beginning each time the pad is triggered.977 |
| LFO Wave | menu_setting | — | Sets the waveform shape for the pad's LFO: Saw, Reverse Saw, Triangle, Positive Triangle, Sine, Positive Sine, Square, Positive Square, or Random.977 |
| Loop End | knob | — | Sample position where looping ends (forward) or begins (reverse); read from and saved to WAV smpl tag; is a modulation target.977 |
| Loop Fade | knob | 0% – 100% | Sets the crossfade overlap length at loop points as a percentage of the loop length; does not work with reverse looping.977 |
| Loop Mode | menu_setting | — | Controls looping direction: None (one-shot), Forward (loops between Loop Start and Loop End), or Bidirect (bounces back and forth).977 |
| Loop Start | knob | ≥0sample | Sample position where looping begins (forward) or ends (reverse); read from and saved to WAV smpl tag; is a modulation target.977 |
| MasterVol | knob | — | Controls the master output volume sent to Out 1 and Out 2; default is 80% at power on.977 |
| MIDI Chan | menu_setting | — | Auto-sampler setting: the MIDI channel used to send out notes that drive the external instrument being sampled. Distinct from a pad's MIDI In listen channel. Range 1 to 16.977 |
| MIDI In | menu_setting | — | Assigns a MIDI channel (Ch1–Ch16 or None) to control this pad chromatically or by slice; multiple pads may share a channel.977 |
| Note Length | menu_setting | — | Auto-sampler setting: in seconds, the length of time the note gate is held on while recording each sampled note. Range 1 to 60.977 |
| Output | menu_setting | — | Routes the pad audio to a selected stereo pair or mono output jack.977 |
| Pad Note | menu_setting | — | Specifies which MIDI note on the MIDI Pads channel triggers this pad; C#-1 maps to MIDI note 0.977 |
| Pan | knob | -100% – 100% | Controls the left/right stereo position for pads routed to stereo outputs; not a modulation target.977 |
| Pan Rnd | knob | 0% – 100% | Randomly pans individual grains across the stereo field; higher values create a wider stereo spread.977 |
| Pitch | knob | -24semitone – 24semitone | Adjusts the pitch of the pad up or down; is a modulation target.977 |
| PlayThru | switch | — | When ON, playback continues past the end of the triggered slice to the end of the file; when OFF, stops at the slice boundary.977 |
| Poly Mode | menu_setting | — | Sets maximum simultaneous voices for the pad (Mono through Poly8 or PolyX); draws from the shared 24-voice pool; does not apply to Granular pads; Gate-triggered pads are monophonic.977 |
| Predelay | knob | 0% – 100% | Delays the signal before reverb is applied, analogous to distance from the walls; is a modulation target.977 |
| Quant Size | menu_setting | — | Snaps playback start and stop to musical grid boundaries; None starts and stops immediately.977 |
| Release | knob | 0% – 100% | Duration of fade-out after note release; uses a logarithmic scale from 0 to 38 seconds; behavior varies by Launch Mode and pad mode; is a modulation target.977 |
| Release Len | menu_setting | — | Auto-sampler setting: in seconds, how long recording continues after the note length ends, to capture the tail of the note. Distinct from the per-pad ADSR Release. Range 1 to 16.977 |
| Res | knob | 0% – 100% | Controls filter resonance — the amount of boost around the filter cutoff frequency; is a modulation target.977 |
| Reverse | switch | — | When ON, plays the WAV file in reverse.977 |
| Root Note | menu_setting | — | Sets the MIDI note at which the sample plays at its native pitch; one semitone of pitch shift per note away from the root. When None, assumes middle C.977 |
| Sample Every | menu_setting | — | Auto-sampler setting: how many semitones separate each recorded WAV file. Set to 1 to record a WAV per note; set to 12 to record one note per octave. Range 1 to 16.977 |
| Scatter | knob | 0% – 100% | Controls how evenly grains are distributed over time; only effective when Density is below 50%.977 |
| Slice | knob | ≥1 | Selects which numbered slice plays when a note is triggered; is a modulation target.977 |
| Slice Seq | menu_setting | — | Advances slice selection on each trigger; options are None, Forward, Backwards, Random, and Stagger; is a modulation target.977 |
| Speed | knob | 0% – 200% | Controls the rate at which grains advance through the WAV file; 100% is normal speed, 50% is half speed, 200% is double speed; is a modulation target.977 |
| Start | knob | ≥0sample | Sets the sample number where forward playback begins (or reverse playback ends); is a modulation target.977 |
| Sustain | knob | 0% – 100% | Sets the volume level the sound maintains while a note is held; not a modulation target.977 |
| Sync | menu_setting | — | Prevents tempo drift by realigning playback to the clock at the specified musical increment while the clip is playing; available only when Quant Size is set.977 |
| Threshold | menu_setting | — | When threshold recording is enabled (Rec Thresh = On), sets the minimum input sound level required to trigger recording to begin. Range -96.00 dB to +0.00 dB.977 |
| Vel Layers | menu_setting | — | Auto-sampler setting: how many velocity layers are captured per note — a separate WAV file can be recorded for each velocity level. Range 1 to 16.977 |
| Width | menu_setting | — | On the Delay FX, sets the width of the range of frequencies included when the delay Filter is on.977 |
| Window | knob | 0% – 100% | Sets the spread of the region around the playback position from which grains are selected; 0% always uses the same position, 100% spans about a few seconds.977 |