# Harmonic Timing Generator (Tobinski)

Canonical page: https://eurorackref.com/tobinski/harmonic-timing-generator/

- id: `tobinski/harmonic-timing-generator`
- width: 18 HP; depth: 27 mm
- power: +12 V 235 mA, −12 V 176 mA, +5 V 20 mA
- status: current
- functions: Analog VCO, 1V/Oct Pitch Tracking, Chord / Paraphonic Oscillator, Simultaneous Waveform Outputs, Master Clock, Clock Divider / Multiplier, Sequential / Voltage Switch, LFO, Gate / Trigger Utility

## Inputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| SELECT 1 CV | cv | selects multiplier output | 0 to 5 V | unipolar | — | 1999 |
| SELECT 2 CV | cv | selects multiplier output | 0 to 5 V | unipolar | — | 1999 |
| SELECT 3 CV | cv | selects multiplier output | 0 to 5 V | unipolar | — | 1999 |
| START IN | gate, trigger | starts the oscillator | ≤ 5 V | unknown | — | 1999 |
| STOP IN | gate, trigger | stops the oscillator | ≤ 5 V | unknown | — | 1999 |
| STEP IN | trigger, clock | one oscillator cycle | 0 to 5 V | unknown | — | 1999 |
| FM | cv, audio | FM input | not stated | unknown | — | 1999 |
| V/OCT | pitch | pitch CV input | not stated | unknown | — | 1999 |
| REF. IN | audio, cv, clock | multiplier reference input | -5 to 5 V | unknown | oscillator saw | 1999 |
| x2 IN | audio, cv, clock | x2 multiplier input | unknown | unknown | REF. IN | 1999 |
| x3 IN | audio, cv, clock | x3 multiplier input | unknown | unknown | REF. IN | 1999 |
| x2 IN (2) | audio, cv, clock | x2 multiplier input | unknown | unknown | OUT 2 | 1999 |
| x5 IN | audio, cv, clock | x5 multiplier input | unknown | unknown | REF. IN | 1999 |
| x2 IN (3) | audio, cv, clock | x2 multiplier input | unknown | unknown | OUT 3 | 1999 |
| x7 IN | audio, cv, clock | x7 multiplier input | unknown | unknown | REF. IN | 1999 |
| x2 IN (4) | audio, cv, clock | x2 multiplier input | unknown | unknown | OUT 4 | 1999 |

## Outputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| SELECT 1 OUT | audio, clock, cv | selected multiplier output | not stated | unknown | SELECT 1, Multiplier section | 1999 |
| SELECT 2 OUT | audio, clock, cv | selected multiplier output | not stated | unknown | SELECT 2, Multiplier section | 1999 |
| SELECT 3 OUT | audio, clock, cv | selected multiplier output | not stated | unknown | SELECT 3, Multiplier section | 1999 |
| TRIANGLE | audio, cv | oscillator triangle wave | -5 to 5 V | bipolar | Oscillator | 1999 |
| SQUARE | audio, cv, clock | oscillator square wave | -5 to 5 V | bipolar | Oscillator | 1999 |
| START OUT | trigger | start pulse output | 0 to 5 V | unipolar | START, START IN | 1999 |
| OUT 1 | audio, clock, cv | x1 falling saw | -5 to 5 V | bipolar | Multiplier section | 1999 |
| OUT 2 | audio, clock, cv | x2 falling saw | -5 to 5 V | bipolar | Multiplier section | 1999 |
| OUT 3 | audio, clock, cv | x3 falling saw | -5 to 5 V | bipolar | Multiplier section | 1999 |
| OUT 4 | audio, clock, cv | x4 falling saw | -5 to 5 V | bipolar | Multiplier section | 1999 |
| OUT 5 | audio, clock, cv | x5 falling saw | -5 to 5 V | bipolar | Multiplier section | 1999 |
| OUT 6 | audio, clock, cv | x6 falling saw | -5 to 5 V | bipolar | Multiplier section | 1999 |
| OUT 7 | audio, clock, cv | x7 falling saw | -5 to 5 V | bipolar | Multiplier section | 1999 |
| OUT 8 | audio, clock, cv | x8 falling saw | -5 to 5 V | bipolar | Multiplier section | 1999 |

## Controls

| Control | Type | Function | Range | Affects | Source |
|---|---|---|---|---|---|
| SELECT 1 buttons | button | manual Select 1 choice | — | SELECT 1 | 1999 |
| SELECT 2 | other | manual select, CV offset | — | SELECT 2 | 1999 |
| SELECT 3 | other | manual select, CV offset | — | SELECT 3 | 1999 |
| RATE | knob | oscillator frequency | — | Oscillator | 1999 |
| LFO | button | LFO mode on/off | — | Oscillator, LFO filtering | 1999 |
| START | button | starts the oscillator | — | Oscillator, START OUT | 1999 |
| STOP | button | stops the oscillator | — | Oscillator | 1999 |
| STEP | button | one oscillator cycle | — | Oscillator | 1999 |
| FINE TUNE | knob | oscillator fine tune | — | Oscillator | 1999 |
| FM | knob | bipolar FM attenuverter | — | FM | 1999 |
| OFFSET | other | saw offset trim | — | Multiplier section | 1999 |
| AMPLITUDE | other | saw amplitude trim | — | Multiplier section | 1999 |
| STEP TRIM | other | step cycle amplitude trim | — | Oscillator | 1999 |
| V/OCT trimmer | other | V/OCT scaling trim | — | V/OCT | 1999 |

## Modes

- LFO mode (LFO = pressed) [1999]
- audio rate (LFO = released) [1999]
- running [1999]
- stopped [1999]

## Specs

| Subject | Quantity | Value | Condition | Source |
|---|---|---|---|---|
| module | width | 18 HP | — | 1999 |
| module | depth | 27 mm | — | 1999 |
| module | +12V current | 235 mA | — | 1999 |
| module | -12V current | 176 mA | — | 1999 |
| module | +5V current | 20 mA | — | 1999 |
| OUT 1-8 | output level | -5 to 5 V | — | 1999 |
| TRIANGLE / SQUARE | output level | -5 to 5 V | — | 1999 |
| START OUT | pulse level | 5 V | — | 1999 |
| SELECT CV | input range | 0 to 5 V | — | 1999 |
| Multiplier section | multiplication | 1 to 8 x | — | 1999 |
| REF. IN | external saw level | -5 to 5 V | — | 1999 |
| V/OCT | accurate tracking range | 4 to 5 octaves | — | 1999 |
| module | warm-up before calibration | 10 to 20 min | — | 1999 |
| inputs | input tolerance | -12 to 12 V | — | 1999 |
| multipliers | x2 stages available | 4 count | — | 1999 |

## Behavior

- START OUT: when START pressed or START IN rises → +5V pulse [1999]
- STEP IN / STEP: when rising edge → one oscillator cycle [1999]
- START IN: when high → oscillator starts [1999]
- STOP IN: when high → oscillator stops [1999]
- LFO button: when pressed → frequency reduced, outputs filtered (LFO mode) [1999]
- LFO filtering: when audio rate use → reduces output amplitude (LFO mode) [1999]
- REF. IN: when unpatched → oscillator saw used [1999]
- x2/x3/x5/x7 IN: when unpatched → REF. IN used [1999]
- x2 IN (2)/(3)/(4): when unpatched → OUT 2/3/4 used [1999]
- Multiplier section: when external saw at REF. IN → runs without internal oscillator [1999]
- SELECT manual control: when CV patched → acts as offset [1999]
- HTG link: when Scanner connected → OUT 1-8 sent to Scanner [1999]
- HTG link: when HTG stopped → outputs sit near -5V [1999]
- V/OCT: when beyond 4-5 octaves → tracking goes sharp [1999]
- STEP IN: when frequency matched to clock → multiplied outputs in sync [1999]
- ramp: when frequency too low → no 0V crossing [1999]

## Sources

- [1999] Tobinski Harmonic Timing Generator manual (manual): https://cdn.prod.website-files.com/61994bad253a4818e1d25973/687be3ba275632117dad18cd_HTG%20Manual%20v1.pdf
- [2000] Tobinski Harmonic Timing Generator product page (product_page): https://www.tobinski-audio.com/modules/harmonic-timing-generator

Full record as JSON: https://eurorackref.com/tobinski/harmonic-timing-generator.json
