# Stereo Dipole (Steady State Fate)

Canonical page: https://eurorackref.com/steady-state-fate/stereo-dipole/

- id: `steady-state-fate/stereo-dipole`
- width: 20 HP; depth: 23 mm
- power: +12 V 150 mA, −12 V 150 mA, +5 V 0 mA
- status: current
- functions: Multimode Filter, Lowpass Filter, Highpass Filter, Bandpass / Notch Filter, Simultaneous Multimode Outputs, Self-Oscillating Filter, 1V/Oct Pitch Tracking, Stereo Inputs / Outputs, Distortion / Saturation, Slew Limiter, LFO

## Inputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| INPUT A | audio, cv | filter channel input | not stated | not stated | — | 816 |
| FM-A | cv | FREQ and SPREAD CV | not stated | not stated | — | 816 |
| RES-A | cv | POLE/DIPOLE resonance CV | not stated | not stated | — | 816 |
| SPRD-A | cv, pitch | secondary cutoff CV | not stated | not stated | — | 816 |
| V/OCT-A | pitch | channel pitch tracking | not stated | not stated | — | 816 |
| INPUT B | audio, cv | filter channel input | not stated | not stated | INPUT A | 816 |
| FM-B | cv | FREQ and SPREAD CV | not stated | not stated | — | 816 |
| RES-B | cv | POLE/DIPOLE resonance CV | not stated | not stated | — | 816 |
| SPRD-B | cv, pitch | secondary cutoff CV | not stated | not stated | — | 816 |
| V/OCT-B | pitch | channel pitch tracking | not stated | not stated | — | 816 |
| V/OCT | pitch | all-filter pitch tracking | not stated | not stated | — | 816 |
| ST-FM | cv | stereo FM CV | not stated | not stated | — | 816 |
| ST-RES | cv | stereo resonance CV | not stated | not stated | — | 816 |

## Outputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| POLE-A | audio | single peak output | not stated | not stated | POLE A | 816 |
| DIPOLE-A | audio | dual peak output | not stated | not stated | DIPOLE A | 816 |
| POLE-B | audio | single peak output | not stated | not stated | POLE B | 816 |
| DIPOLE-B | audio | dual peak output | not stated | not stated | DIPOLE B | 816 |
| DIPOLE AB | audio | quad peak mono output | not stated | not stated | DIPOLE AB | 816 |

## Controls

| Control | Type | Function | Range | Affects | Source |
|---|---|---|---|---|---|
| FREQ A | knob | primary and secondary cutoff | — | POLE A, DIPOLE A | 817 |
| SPREAD A | knob | secondary cutoff offset | -5 to 5 octaves | DIPOLE A | 817 |
| RES A | knob | both peaks resonance | — | POLE A, DIPOLE A | 816 |
| DRIVE A | knob | pre-filter drive | — | DRIVE A | 816 |
| POLE type switch A | switch | POLE filter type | — | POLE-A | 817 |
| DIPOLE type switch A | switch | DIPOLE filter type | — | DIPOLE-A | 817 |
| routing switch A | switch | DIPOLE serial/parallel routing | — | DIPOLE A, DIPOLE AB | 816 |
| FM LVL A | other | bipolar FM attenuator | — | FM-A, ST-FM | 816 |
| RCV LVL A | other | unipolar RES CV attenuator | — | RES-A | 816 |
| FREQ B | knob | primary and secondary cutoff | — | POLE B, DIPOLE B | 817 |
| SPREAD B | knob | secondary cutoff offset | -5 to 5 octaves | DIPOLE B | 817 |
| RES B | knob | both peaks resonance | — | POLE B, DIPOLE B | 816 |
| DRIVE B | knob | pre-filter drive | — | DRIVE B | 816 |
| POLE type switch B | switch | POLE filter type | — | POLE-B | 817 |
| DIPOLE type switch B | switch | DIPOLE filter type | — | DIPOLE-B | 817 |
| routing switch B | switch | DIPOLE serial/parallel routing | — | DIPOLE B, DIPOLE AB | 816 |
| FM LVL B | other | bipolar FM attenuator | — | FM-B, ST-FM | 816 |
| RCV LVL B | other | unipolar RES CV attenuator | — | RES-B | 816 |
| STEREO FREQ | knob | all four cutoffs | -10 to 10 octaves | POLE A, DIPOLE A, POLE B, DIPOLE B | 816 |
| STEREO RES | knob | bipolar all-filter resonance | — | POLE A, DIPOLE A, POLE B, DIPOLE B | 816 |
| ST-FM attenuator | other | ST-FM master level | — | ST-FM | 816 |
| ST-RES attenuator | other | ST-RES master level | — | ST-RES | 816 |

## Modes

- SERIAL (routing switch A = SERIAL) [816]
- PARALLEL (routing switch A = PARALLEL) [816]

## Specs

| Subject | Quantity | Value | Condition | Source |
|---|---|---|---|---|
| STEREO FREQ | range | -10 to 10 octaves | — | 816 |
| cutoff | total usable range | 17 octaves | — | 816 |
| cutoff | maximum | 50 kHz | — | 816 |
| cutoff | minimum from controls | 0.3 Hz | — | 816 |
| SPREAD | offset range | -5 to 5 octaves | — | 817 |
| self-oscillation | bandwidth | ≥ 20 octaves | — | 817 |
| series POLE+DIPOLE | slope | 24 dB/oct | SERIAL, same filter type | 817 |
| module | width | 20 hp | — | 817 |
| module | depth | 23 mm | — | 817 |
| module | current +12V | 150 mA | — | 817 |
| module | current -12V | 150 mA | — | 817 |
| module | current 5V | 0 mA | — | 817 |

## Behavior

- INPUT B: when unpatched → receives INPUT A [816]
- DRIVE: when lowest position → passes without gain [816]
- DRIVE: when heavy use → soft then hard clipping [816]
- SPREAD: when center position → matches primary cutoff [817]
- FM-A/B: when negative CV → cutoff below 0.3Hz [816]
- SPRD-A/B: when no attenuator → accurate 1V/OCT secondary [816]
- FM LVL: when center → FM off [816]
- STEREO RES: when roughly center → default position [816]
- input: when gate edges, high resonance → fires pluck [816]
- DIPOLE filter type: when SERIAL mode → affects oscillation tone [816]
- HP POLE, LP DIPOLE: when SERIAL, SPREAD above center → variable width bandpass [816]
- HP POLE, LP DIPOLE: when PARALLEL → variable width notch [816]

## Sources

- [816] SSF Stereo Dipole Cheat Sheet (manual): https://cdn.shopify.com/s/files/1/0616/1206/4946/files/ssf-stereo-dipole-cheat-sheet.pdf?v=1651524873
- [817] SSF Stereo Dipole product page (product_page): https://steadystatefate.com/products/stereo-dipole

Full record as JSON: https://eurorackref.com/steady-state-fate/stereo-dipole.json
