# Angle Grinder (Schlappi Engineering)

Canonical page: https://eurorackref.com/schlappi-engineering/angle-grinder/

- id: `schlappi-engineering/angle-grinder`
- width: 18 HP; depth: unknown mm
- power: +12 V 81 mA, −12 V 78 mA, +5 V ? mA
- status: current
- functions: Analog VCO, 1V/Oct Pitch Tracking, Phase-offset outputs, Linear FM, Exponential FM, LFO, Lowpass Filter, Highpass Filter, Bandpass / Notch Filter, Simultaneous Multimode Outputs, Distortion / Saturation

## Inputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| IN | audio, cv | GRIND input | not stated | not stated | 90 output via ALL PASS filter | 737 |
| INJECT | audio, cv | direct input to SPIN | not stated | not stated | — | 737 |
| V/OCT | cv | volts per octave | not stated | not stated | — | 737 |
| FM 1 | cv, audio | FM over SPIN | not stated | not stated | GRIND OUT | 737 |
| FM 2 | cv | exponential CV over SPIN | not stated | not stated | — | 737 |
| GRIND CV 1 | cv | GRIND slider CV | 0 to 5 V | unipolar | — | 737 |
| GRIND CV 2 | cv | GRIND slider CV | 0 to 5 V | unipolar | — | 737 |
| GRIND CV 3 | cv | GRIND slider CV | 0 to 5 V | unipolar | — | 737 |
| GRIND CV 4 | cv | GRIND slider CV | 0 to 5 V | unipolar | — | 737 |

## Outputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| GRIND OUT | audio | GRIND output | -11 to 11 V | not stated | GRIND | 737 |
| SPIN 0 | audio, cv | 0 phase sine | -2.5 to 2.5 V | bipolar | SPIN | 737 |
| SPIN 90 | audio, cv | 90 phase sine | -2.5 to 2.5 V | bipolar | SPIN | 737 |
| SPIN 180 | audio, cv | 180 phase sine | -2.5 to 2.5 V | bipolar | SPIN | 737 |
| SPIN 270 | audio, cv | 270 phase sine | -2.5 to 2.5 V | bipolar | SPIN | 737 |

## Controls

| Control | Type | Function | Range | Affects | Source |
|---|---|---|---|---|---|
| GRIND SLIDER 1 | fader | signal amount to grind | — | GRIND | 737 |
| GRIND SLIDER 2 | fader | signal amount to grind | — | GRIND | 737 |
| GRIND SLIDER 3 | fader | signal amount to grind | — | GRIND | 737 |
| GRIND SLIDER 4 | fader | signal amount to grind | — | GRIND | 737 |
| SPIN | knob | coarse tuning | — | SPIN | 737 |
| FINE | knob | fine tuning | — | SPIN | 737 |
| RANGE SWITCH | switch | frequency range | — | SPIN | 737 |
| GRIND -> SPIN | knob | feeds GRIND into SPIN | — | SPIN, GRIND | 737 |
| DAMPING | knob | counteracts oscillations | — | SPIN | 737 |
| FM 1 | knob | FM 1 attenuator | — | FM 1, SPIN | 737 |
| GRIND IN | knob | input level to GRIND | — | GRIND, IN | 737 |
| FM1 header | jumper | FM 1 response | — | FM 1 | 737 |
| INJECT header | jumper | INJECT coupling | — | INJECT | 737 |

## Modes

- oscillate [737]
- filter [737]
- LOW range (RANGE SWITCH = LOW) [737]
- HIGH range (RANGE SWITCH = HIGH) [737]

## Specs

| Subject | Quantity | Value | Condition | Source |
|---|---|---|---|---|
| SPIN | frequency range | 10 to 20000 Hz | HIGH range | 737 |
| SPIN | frequency range | 0.3 to 600 Hz | LOW range (specifications) | 737 |
| SPIN | frequency range | 0.1 to 500 Hz | LOW range (panel legend) | 737 |
| SPIN | frequency range | 0.3 to 500 Hz | LOW range | 738 |
| V/OCT | tracking | ≥ 4 octaves | — | 737 |
| SPIN outputs | sine amplitude | 5 Vpp | — | 737 |
| GRIND and filter outputs | maximum amplitude | ≤ 22 Vpp | — | 737 |
| module | width | 18 HP | — | 737 |
| module | current +12V | 81 mA | — | 737 |
| module | current -12V | 78 mA | — | 737 |

## Behavior

- FM 1 jack: when unpatched → normalled to GRIND OUT [737]
- FM 1 knob: when tracking pitch, FM unpatched → turn down [737]
- IN jack: when unpatched → 90 output via all-pass [737]
- GRIND section: when GRIND IN knob down → no GRIND output [737]
- SPIN: when GRIND -> SPIN, DAMPING CCW → four phase-related sines [737]
- SPIN: when damped or enough GRIND feedback → stops oscillating, becomes filter [737]
- SPIN: when external IN, GRIND -> SPIN CW → outputs become LP/BP/HP/inv BP (filter) [737]
- DAMPING: when turned up → lets external signal through [738]
- GRIND sliders: when filter mode → nonlinear feedback paths (filter) [737]
- GRIND OUT: when more sliders raised → converges on pyramidal shape (oscillate) [737]
- GRIND OUT: when external input, SPIN low frequency → resembles supersaw [737]
- GRIND OUT: when external input, SPIN audio rate → metallic overtones [737]
- INJECT: when AC coupled → input becomes reset spikes [737]
- INJECT: when DC coupled, large input → adds to signal, may clip [737]
- GRIND OUT: when waveform shape → varies by frequency [737]

## Sources

- [737] Schlappi Engineering Angle Grinder Manual (manual): https://cdn.shopify.com/s/files/1/0549/4538/2479/files/angle_grinder_manual_20181022.pdf
- [738] Schlappi Engineering Angle Grinder product page (product_page): https://schlappiengineering.com/products/angle-grinder

Full record as JSON: https://eurorackref.com/schlappi-engineering/angle-grinder.json
