# A-196 (Doepfer)

Canonical page: https://eurorackref.com/doepfer/a-196/

- id: `doepfer/a-196`
- width: 8 HP; depth: 40 mm
- power: +12 V 40 mA, −12 V 0 mA, +5 V ? mA
- status: current
- functions: Send / return

## Inputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| VCO CV In | cv | VCO control voltage | not stated | unknown | Low Pass Out | 1858 |
| PC In 1 | audio | phase comparator input 1 | not stated | unknown | VCO Out | 1858 |
| PC In 2 | audio | external signal input | not stated | unknown | — | 1858 |

## Outputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| VCO Out | audio, clock | VCO rectangle output | not stated | unknown | VCO | 1858 |
| PC Out | gate | phase comparator output | not stated | unknown | phase comparator | 1858 |
| Low Pass Out | cv | low pass filter output | not stated | unknown | low pass filter | 1858 |

## Controls

| Control | Type | Function | Range | Affects | Source |
|---|---|---|---|---|---|
| Range | switch | VCO frequency range | — | VCO | 1858 |
| Offs. | knob | VCO frequency offset | 0 to 10 | VCO | 1858 |
| Type | switch | phase comparator select | — | phase comparator | 1858 |
| Frequ. | knob | low pass frequency | — | low pass filter | 1858 |
| JP3 | jumper | In 1 coupling | — | PC In 1 | 1859 |
| JP4 | jumper | In 2 coupling | — | PC In 2 | 1859 |

## Modes

- PC1 (Type = 1) [1858]
- PC2 (Type = 2) [1858]
- PC3 (Type = 3) [1858]

## Specs

| Subject | Quantity | Value | Condition | Source |
|---|---|---|---|---|
| VCO | frequency range | 2 to 50 Hz | Range low, Offset 0, CV 0...+5V | 1858 |
| VCO | frequency range | 2 to 200 Hz | Range low, Offset 5, CV 0...+5V | 1858 |
| VCO | frequency range | 2 to 1000 Hz | Range low, Offset 10, CV 0...+5V | 1858 |
| VCO | frequency range | 20 to 500 Hz | Range mid, Offset 0, CV 0...+5V | 1858 |
| VCO | frequency range | 20 to 2000 Hz | Range mid, Offset 5, CV 0...+5V | 1858 |
| VCO | frequency range | 20 to 10000 Hz | Range mid, Offset 10, CV 0...+5V | 1858 |
| VCO | frequency range | 200 to 5000 Hz | Range high, Offset 0, CV 0...+5V | 1858 |
| VCO | frequency range | 200 to 20000 Hz | Range high, Offset 5, CV 0...+5V | 1858 |
| VCO | frequency range | 100 to 100000 Hz | Range high, Offset 10, CV 0...+5V | 1858 |
| module | width | 8 HP | — | 1859 |
| module | depth | 40 mm | — | 1859 |
| module | +12V current | 40 mA | — | 1859 |
| module | -12V current | 0 mA | Version 1 | 1859 |
| module | -12V current | 10 mA | Version 2 and 3 | 1859 |
| PLL | tracking range | 30 to 1000 Hz | recommended initial settings | 1859 |
| PC In 2 | serial resistor | 1000 ohm | — | 1859 |
| PC In 2 | protection Zener | 5 V | — | 1859 |

## Behavior

- VCO CV In: when unpatched → from Low Pass Out [1858]
- PC In 1: when unpatched → from VCO Out [1858]
- PC Out: when always → feeds low pass filter [1858]
- PC1: when harmonic frequency ratio → locks at harmonics (PC1) [1858]
- LED: when PLL locked → lights (PC2) [1858]
- PLL: when external frequency higher → CV increases [1858]
- PLL: when external frequency lower → CV decreases [1858]
- PLL: when frequencies identical → CV stops changing [1858]
- VCO: when LP frequency too high → frequency jitters [1858]
- VCO: when LP frequency very low → noticeable slew [1858]
- VCO: when CV 0V → VCO stops [1859]
- PC In 1: when JP3 installed → DC coupled [1859]
- PC In 1: when JP3 removed → AC coupled [1859]
- PC In 2: when JP4 installed → DC coupled [1859]
- PC In 2: when JP4 removed → AC coupled [1859]
- PC In 2: when Zener protection → may clip input [1859]
- external low pass: when replacing internal LP → must be DC coupled [1858]

## Sources

- [1858] Doepfer A-196 manual (manual): https://doepfer.de/a100_man/A196_man.pdf
- [1859] Doepfer A-196 product page (product_page): https://doepfer.de/a196.htm

Full record as JSON: https://eurorackref.com/doepfer/a-196.json
