# A-147-2 (Doepfer)

Canonical page: https://eurorackref.com/doepfer/a-147-2/

- id: `doepfer/a-147-2`
- width: 8 HP; depth: 55 mm
- power: +12 V 60 mA, −12 V 40 mA, +5 V ? mA
- status: current
- functions: LFO, Simultaneous Waveform Outputs, Oscillator Sync, VCA, Ring Modulator, ADSR Envelope, Attenuverter / Offset

## Inputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| LFO CV | cv | LFO frequency CV | not stated | unknown | fixed voltage (JP6 jumper) | 1833 |
| LFO Reset | trigger, gate, clock | LFO reset/sync | unknown | unknown | — | 1833 |
| VCA In | cv, audio | VCA signal input | not stated | unknown | Triangle Out | 1833 |
| VCA CV | cv | VCA control input | 0 to 5 V | unipolar | Delay Out | 1833 |
| Delay CV | cv | delay time CV | not stated | unknown | — | 1833 |
| Delay Reset | gate, clock, trigger | resets delay voltage | unknown | unknown | — | 1833 |

## Outputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| Triangle Out | cv | LFO triangle | -4 to 4 V | bipolar | VCLFO | 1833 |
| Sine Out | cv | LFO sine | -4 to 4 V | bipolar | VCLFO | 1833 |
| Sawtooth Out | cv | LFO rising sawtooth | 0 to 8 V | unipolar | VCLFO | 1833 |
| Rectangle Out | cv | LFO rectangle | -4 to 4 V | bipolar | VCLFO | 1833 |
| VCA Out | cv, audio | VCA signal output | not stated | unknown | VCA | 1833 |
| Delay Out | cv | delay envelope output | 0 to 5 V | unipolar | Delay unit | 1833 |

## Controls

| Control | Type | Function | Range | Affects | Source |
|---|---|---|---|---|---|
| LFO Frequency | knob | LFO frequency | — | VCLFO | 1833 |
| CV | knob | LFO CV amount | — | LFO CV, VCLFO | 1833 |
| CV Mode | switch | CV control function | — | CV | 1833 |
| VCA Mode | switch | VCA function | — | VCA | 1833 |
| Delay | knob | delay/attack time | 0.005 to 120 s | Delay unit | 1833 |
| JP6 | jumper | ultra-low mode | — | LFO CV, VCLFO | 1833 |

## Modes

- CV attenuator (CV Mode = attenuator) [1833]
- CV polarizer (CV Mode = polarizer) [1833]
- VCA (VCA Mode = VCA) [1833]
- Polarizer (VCA Mode = polarizer) [1833]
- Ultra-low (JP6 = JP6 set) [1833]

## Specs

| Subject | Quantity | Value | Condition | Source |
|---|---|---|---|---|
| module | width | 8 HP | — | 1833 |
| module | depth | 55 mm | — | 1833 |
| module | +12V current | 60 mA | — | 1833 |
| module | -12V current | 40 mA | — | 1833 |
| VCLFO | frequency | 0.005 to 200 Hz | without external CV | 1833 |
| VCLFO | frequency | ≤ 1000 Hz | with external CV | 1833 |
| VCLFO | period | 180 s | slowest, without external CV | 1833 |
| VCLFO | period | 3600 s | ultra-low mode or external CV | 1833 |
| VCA | gain | 0 to 1 x | VCA mode, CV 0 to +5V | 1833 |
| VCA | gain | -0.5 to 0.5 x | polarizer mode, CV 0 to +5V | 1833 |
| VCA | null CV | 2.5 V | polarizer mode | 1833 |
| Delay unit | delay time | 0.005 to 120 s | without Delay CV | 1833 |
| Delay unit | output level | 0 to 5 V | — | 1833 |
| LFO Reset/Delay Reset | trigger level | ≥ 6 Vpp | — | 1833 |

## Behavior

- VCA In: when unpatched → receives LFO triangle [1833]
- VCA CV: when unpatched → receives Delay Out [1833]
- Delay unit: when Delay Reset rising edge → output resets to 0V [1833]
- Delay unit: when after reset → rises linearly to +5V [1833]
- Delay unit: when reaches +5V → holds until next reset [1833]
- Delay: when fully clockwise → about 5 ms [1833]
- Delay: when fully counterclockwise → about 2 minutes [1833]
- Delay CV: when external CV applied → range extended [1833]
- VCA: when CV about +5V → gain +1 (VCA) [1833]
- VCA: when CV 0V → gain -0.5 (inverted) (Polarizer) [1833]
- VCA: when CV about +2.5V → signal suppressed (Polarizer) [1833]
- CV: when left of center → CV reduces LFO frequency (CV polarizer) [1833]
- CV: when center position → CV has no effect (CV polarizer) [1833]
- CV: when right of center → acts as attenuator (CV polarizer) [1833]
- LFO CV: when JP6 set, unpatched → fixed voltage applied [1833]
- VCLFO: when ultra-low, CV polarizer → periods up to 1 hour+ [1833]
- LFO Reset/Delay Reset: when slow-slope signal → not suitable [1833]
- LFO Reset/Delay Reset: when below about 6 Vpp → level shifter recommended [1833]

## Sources

- [1833] Doepfer A-147-2 product page (product_page): https://doepfer.de/a1472.htm

Full record as JSON: https://eurorackref.com/doepfer/a-147-2.json
