# A-136 (Doepfer)

Canonical page: https://eurorackref.com/doepfer/a-136/

- id: `doepfer/a-136`
- width: 8 HP; depth: 45 mm
- power: +12 V 30 mA, −12 V 10 mA, +5 V ? mA
- status: current
- functions: Distortion / Saturation

## Inputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| Input | audio, cv | signal input | not stated | unknown | not stated | 1828 |
| Ext. Level (+L) | cv | positive clipping level CV | not stated | unknown | — | 1828 |
| Ext. Level (-L) | cv | negative clipping level CV | not stated | unknown | — | 1828 |

## Outputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| Output | audio, cv | signal output | not stated | unknown | Waveshaper | 1828 |

## Controls

| Control | Type | Function | Range | Affects | Source |
|---|---|---|---|---|---|
| A | knob | original signal amplification | -4 to 4 x | Waveshaper | 1828 |
| +L | knob | positive clipping level | 0 to 10 scale | Waveshaper | 1828 |
| -L | knob | negative clipping level | 0 to 10 scale | Waveshaper | 1828 |
| +A | knob | positive component amplification | -4 to 4 x | Waveshaper | 1828 |
| -A | knob | negative component amplification | -4 to 4 x | Waveshaper | 1828 |
| JP2 | jumper | input coupling select | — | Input | 1829 |

## Specs

| Subject | Quantity | Value | Condition | Source |
|---|---|---|---|---|
| module | width | 8 HP | — | 1829 |
| module | width | 40.3 mm | — | 1829 |
| module | depth | 45 mm | — | 1829 |
| module | +12V current | 30 mA | — | 1829 |
| module | -12V current | 10 mA | — | 1829 |
| A | amplification factor | -4 to 4 x | — | 1828 |
| A | amplification at setting 0 | -4 x | — | 1828 |
| A | amplification at setting 3.5 | -1 x | — | 1828 |
| A | amplification at setting 5 | 0 x | — | 1828 |
| A | amplification at setting 6.5 | 1 x | — | 1828 |
| A | amplification at setting 10 | 4 x | — | 1828 |
| Input | pre-amp clipping level | 7 Vpp | — | 1829 |

## Behavior

- +L knob: when Ext. Level (+L) patched → no function; CV sets level [1828]
- -L knob: when Ext. Level (-L) patched → no function; CV sets level [1828]
- +A section: when input above +L → amplification +A applies [1828]
- -A section: when input below -L → amplification -A applies [1828]
- +A section: when input never exceeds +L → no effect [1828]
- Ext. Level: when unsuitable CV applied → may not work properly [1828]
- Input: when signals above ~7 Vpp → clips at pre-amp [1829]
- JP2: when removed → AC-coupled input [1829]
- JP2: when LFO processing → must be installed [1829]

## Sources

- [1828] Doepfer A-136 manual (manual): https://doepfer.de/a100_man/A136_man.pdf
- [1829] Doepfer A-136 product page (product_page): https://doepfer.de/a136.htm

Full record as JSON: https://eurorackref.com/doepfer/a-136.json
