# A-110-1 Standard VCO (Doepfer)

Canonical page: https://eurorackref.com/doepfer/a-110-1/

- id: `doepfer/a-110-1`
- width: 10 HP; depth: 55 mm
- power: +12 V 90 mA, −12 V 20 mA, +5 V ? mA
- status: current
- functions: Analog VCO, 1V/Oct Pitch Tracking, Simultaneous Waveform Outputs, Pulse Width Modulation, Oscillator Sync, Exponential FM

## Inputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| SYNC | audio | hard sync input | not stated | unknown | — | 205 |
| CV 1 | pitch, cv | pitch CV, 1V/oct | not stated | unknown | System Bus CV | 205 |
| CV 2 | pitch, cv | FM / pitch CV | not stated | unknown | — | 205 |
| PW CV 1 | cv | PWM input 1 | not stated | unknown | — | 205 |
| PW CV 2 | cv | PWM input 2 | not stated | unknown | — | 205 |

## Outputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| Sawtooth | audio | sawtooth output | unknown | unknown | VCO | 205 |
| Square | audio | square wave output | unknown | unknown | VCO, waveform converters | 205 |
| Triangle | audio | triangle wave output | unknown | unknown | VCO, waveform converters | 205 |
| Sine | audio | sine wave output | unknown | unknown | VCO, waveform converters | 205 |

## Controls

| Control | Type | Function | Range | Affects | Source |
|---|---|---|---|---|---|
| Range | switch | octave / footage switch | — | VCO | 205 |
| Tune | knob | fine tuning | -6 to 6 semitones | VCO | 205 |
| CV 2 | knob | CV 2 attenuator | — | CV 2, VCO | 205 |
| PW | knob | manual pulse width | — | Square | 205 |
| PW CV 2 | knob | PW CV 2 attenuator | — | PW CV 2, Square | 205 |
| INT.CV | jumper | bus CV normalling | — | CV 1 | 206 |

## Specs

| Subject | Quantity | Value | Condition | Source |
|---|---|---|---|---|
| VCO | frequency range | 10 octaves | manual figure | 205 |
| VCO | frequency range | 15 to 8000 Hz | product page figure | 206 |
| Tune | range | -1 to 1 semitones | older modules | 206 |
| Tune | range | -0.5 to 0.5 octaves | since about mid 2015 | 206 |
| Sawtooth, Square | output level | 8 Vpp | typical | 206 |
| Triangle, Sine | output level | 10 Vpp | typical | 206 |
| VCO | warm-up time | 20 min | — | 205 |
| Range | switch positions | 10 positions | only 5 marked usable | 206 |
| module | width | 10 HP | — | 206 |
| module | depth | 55 mm | — | 206 |
| module | current +12V | 90 mA | — | 206 |
| module | current -12V | 20 mA | — | 206 |

## Behavior

- CV 1: when unpatched → follows System Bus CV [205]
- CV 1: when plug inserted → bus CV disconnected [205]
- INT.CV jumper: when removed → bus normalling removed [206]
- SYNC: when master cycle starts → slave sawtooth resets [205]
- Range: when positions beyond -2..+2 → should not be used [206]

## Sources

- [205] A-110-1 Standard VCO Manual (manual): https://doepfer.de/a100_man/a110_man.pdf
- [206] Doepfer A-110-1 product page (product_page): https://doepfer.de/a110.htm

Full record as JSON: https://eurorackref.com/doepfer/a-110-1.json
