# Tapographic Delay (4ms)

Canonical page: https://eurorackref.com/4ms/tapographic-delay/

- id: `4ms/tapographic-delay`
- width: 18 HP; depth: 25 mm
- power: +12 V 125 mA, −12 V 32 mA, +5 V 0 mA
- status: current
- functions: Delay, Lowpass Filter, Bandpass / Notch Filter, Stereo Inputs / Outputs, Stereo Panning, Tempo / Clock Sync, Clock Divider / Multiplier, Freeze / Hold, Trigger / Euclidean Sequencer

## Inputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| Audio In | audio | audio input | -11 to 11 V | not stated | — | 168 |
| Time CV | cv | tap time CV | -5 to 5 V | bipolar | — | 168 |
| Feedback CV | cv | feedback CV | -5 to 5 V | bipolar | — | 168 |
| Modulation CV | cv | modulation CV | -5 to 5 V | bipolar | — | 168 |
| Dry/Wet CV | cv | dry/wet CV | -5 to 5 V | bipolar | — | 168 |
| Repeat | trigger | Repeat toggle | 2 to 12 V | unknown | — | 168 |
| Tap/Next | trigger | tap entry trigger | 2 to 12 V | unknown | — | 168 |
| Velocity/Morph | cv | tap velocity CV | 0 to 8 V | unipolar | VEL NORM jumper | 168 |
| Ext Clock | clock | external clock | 2 to 12 V | unknown | — | 168 |

## Outputs

| Jack | Signals | Function | Voltage | Polarity | Normalled from / comes from | Source |
|---|---|---|---|---|---|---|
| Audio Out 1 | audio | stereo audio output | -8.5 to 8.5 V | unknown | taps, delay line | 168 |
| Audio Out 2 | audio | stereo audio output | -8.5 to 8.5 V | unknown | taps, delay line | 168 |
| Gate Out | trigger | tapography trigger pattern | 0 to 8 V | unipolar | taps | 168 |

## Controls

| Control | Type | Function | Range | Affects | Source |
|---|---|---|---|---|---|
| Level | knob | wet input level | 0 to 300 % | delay line | 168 |
| Time | knob | tap time scale | 0.1 to 4 factor | delay line, taps, Gate Out | 168 |
| Feedback | knob | feedback amount | 0 to 120 % | Feedback path | 168 |
| Modulation | knob | LFO amount/frequency | — | modulation LFOs | 168 |
| Dry/Wet | knob | dry/wet mix | — | Audio Out 1, Audio Out 2 | 168 |
| Morph | knob | transition time | 0 to 12 s | delay line, tapography sequencer | 168 |
| ADD/OFF/INS | switch | tap insertion mode | — | taps, tapography sequencer | 168 |
| RES/AMP/LPF | switch | tap velocity destination | — | taps, tap filter | 168 |
| Repeat/Clear | button | Repeat toggle / clear | — | Repeat feedback path, taps | 168 |
| Delete/Sync | button | delete tap / Sync | — | taps, clock sync | 168 |
| Tap sensor | other | velocity-sensitive tap entry | — | taps, tapography sequencer | 168 |
| Tap Buttons 1-6 | button | load/save tapographies | — | delay line | 168 |
| VEL NORM jumper | jumper | Velocity/Morph normalization | — | Velocity/Morph | 168 |
| VEL | menu_setting | velocity mapping amount | — | taps, tap filter | 168 |
| BANK | menu_setting | active bank | — | Tap Buttons 1-6 | 168 |
| PAN | menu_setting | stereo panning mode | — | Audio Out 1, Audio Out 2 | 168 |
| MODE | menu_setting | edit or sequencer mode | — | taps, tapography sequencer | 168 |

## Modes

- EDIT (MODE = EDIT) [168]
- SEQ (MODE = SEQ) [168]
- Sync [168]
- Repeat [168]
- ADD (ADD/OFF/INS = ADD) [168]
- INS (ADD/OFF/INS = INS) [168]
- OFF (ADD/OFF/INS = OFF) [168]
- PAN ALT (PAN = ALT) [168]
- PAN RND (PAN = RND) [168]
- PAN SUM/R (PAN = SUM/R) [168]

## Specs

| Subject | Quantity | Value | Condition | Source |
|---|---|---|---|---|
| delay line | maximum delay time | 174 s | — | 168 |
| taps | maximum taps | 32 taps | — | 168 |
| tapography memory | slots | 24 slots | 4 banks of 6 | 168 |
| Level | input gain | 0 to 300 % | — | 168 |
| Time | time scale factor | 0.1 to 4 x | middle = 1 | 168 |
| Time | clock multiply/divide | 0.125 to 16 ratio | Sync engaged | 168 |
| Feedback | feedback amount | 0 to 120 % | — | 168 |
| Modulation | LFO frequency | 50 Hz | fully counter-clockwise | 168 |
| Modulation | LFO depth | 0.5 s | fully clockwise, +/- | 168 |
| Morph | transition time | 0 to 12 s | — | 168 |
| tap filter | RES resonance Q | 1 to 20 Q | set by VEL | 168 |
| module | sample rate | 48 kHz | — | 168 |
| module | bit depth | 16 bits | — | 168 |
| module | internal processing | 32 bits float | — | 168 |
| module | software latency | 1.3 ms | — | 168 |
| Audio In | maximum level | 22 Vpp | — | 168 |
| Audio Out | soft-limit maximum | 17 Vpp | — | 168 |
| dry path | frequency response flatness | 0.1 dB | 20 Hz–5 kHz, +/- | 168 |
| dry path | response at 10 kHz | -2.3 dB | — | 168 |
| dry path | response at 20 kHz | -7.8 dB | — | 168 |
| module | width | 18 HP | — | 168 |
| module | depth | 25 mm | — | 168 |
| module | +12V current | 125 mA | — | 168 |
| module | -12V current | 32 mA | — | 168 |
| module | +5V current | 0 mA | — | 169 |

## Behavior

- first tap after Clear: when tap sensor or Tap/Next → starts recording, velocity ignored [168]
- new tap: when exceeds 32 taps → oldest tap fades out [168]
- new tap: when ADD position → appended; tapography lengthens [168]
- new tap: when INS position → inserted; length unchanged [168]
- Tap sensor and Tap/Next: when OFF position → no effect [168]
- Tap LED: when tapography cleared or OFF → turns off [168]
- tapography changes: when any change → transitions over Morph time [168]
- Repeat: when enabled → last tap fed back unity [168]
- Repeat loop size: when Time knob moved → not scaled [168]
- Clear: when held → no undo [168]
- Sync: when engaged → length synced to Ext Clock [168]
- Time knob: when Sync engaged → selects clock multiply/divide [168]
- Time: when knob moving → temporary pitch shift [168]
- Modulation: when fully counter-clockwise → no audible effect [168]
- Modulation: when fully clockwise → LFOs stalled at position [168]
- CV inputs: when positive voltage → adds to knob [168]
- CV inputs: when negative voltage → subtracts from knob [168]
- Velocity/Morph: when trigger on Tap/Next → sampled as velocity [168]
- Velocity/Morph: when unpatched, VEL NORM HIGH → maximum velocity [168]
- Velocity/Morph: when unpatched, VEL NORM TAP → velocity from trigger amplitude [168]
- Velocity/Morph: when SEQ, unpatched, VEL NORM HIGH → zero volts, fast morph (SEQ) [168]
- Velocity/Morph: when SEQ mode → higher voltage, slower transition (SEQ) [168]
- sequencer: when OFF position → forward, wraps 6→1 (SEQ) [168]
- sequencer: when ADD position → random slot (SEQ) [168]
- sequencer: when INS position → random walk (SEQ) [168]
- sequencer: when advanced by pad → Velocity/Morph CV ignored (SEQ) [168]
- sequencer: when advanced by Tap/Next → pad pressure ignored (SEQ) [168]
- sequencer: when harder pad tap → faster transition (SEQ) [168]
- tapography editing: when SEQ mode → disabled (SEQ) [168]
- PAN setting: when new setting chosen → re-pans all existing taps [168]
- VEL: when MIN, LPF/AMP taps → full velocity sensitivity [168]
- VEL: when MAX, LPF/AMP taps → no sensitivity, maximum amplitude [168]
- VEL: when RES taps → sets Q 1–20 [168]
- start-up: when power on → last slot loaded [168]
- saved state: when power cycle → saved only on menu entry [168]
- save: when button released, not re-pressed → save aborted [168]
- settings: when changed during performance → may click or glitch [168]
- loaded slot: when tapography edited → green light off [168]

## Sources

- [168] Tapographic Delay User Manual v1.0 (manual): https://4mscompany.com/TAPO/Tapographic-Delay-User-Manual-1_0.pdf
- [169] 4ms Tapographic Delay product page (product_page): https://4mscompany.com/tapo.php

Full record as JSON: https://eurorackref.com/4ms/tapographic-delay.json
